Hobart ML-134306 Instrukcja Użytkownika

701 S. RIDGE AVENUE TROY, OHIO 45374-0001937-332-3000 · WWW.HOBARTCORP.COMModelsHL800 ML-134306HL1400 ML-134343Prior MLs Coveredin this Manual

– 10 –BOWL PLACEMENTNOTE: The bowl must be installed onto the bowl support before the agitator is installed.To Install 1. Fully lower the bowl suppo

– 11 –POWER BOWL LIFTCAUTION: Before lowering the bowl onto a bowl truck, always unlock bowl and swing bowl out slightly.To raise the bowl, the bowl

– 12 –TIMER OPERATIONUsing the Count-Up Mode (Continuous Mixing) 1. Turn the SPEED dial to select a mix speed (the SPEED setting can be changed at a

– 13 –Using the Count-Down Mode (Timed Mixing) 1. Turn the SPEED dial to select a mix speed.a. If the count-up mode was used for the previous batch

– 14 –Recipe Mode — To Enter and Exit • To enter recipe mode, press any recipe button. The recipe button lights to indicate you are in Recipe Mode,

– 15 –Running a Recipe • Select the desired recipe by pressing the recipe button. The button lights and step one of the recipe displays. • Press ST

– 16 –Entering a Special FunctionSpecial Function Mode allows you to access three user resettable parameters: • Programming Recipes, (SEt . . .rE

– 17 –Programming a Recipe [SEt . . . rECP]This function allows you to program any of 9 mixer recipes with up to 6 steps in each recipe.Follow instruc

– 18 –Making a Recipe Active or Inactive [Atth . . . rECP]This function allows you to change the status of a recipe from Active to Inactive or vice ve

– 19 –Setting the Access Code [SEt . . . CodE]This function allows you to change the factory-set access code, 0015, to any number from 0000 to 9999.

– 2 –LEGACY 80-QUART AND 140-QUART MIXERS

– 20 –UNLOADING 1. After the mixer has stopped, unlock the bowl and swing-out slightly. Press and hold the down arrow on the bowl switch to lower th

– 21 –Remove and Clean Wire Cage (Fig. 10) 1. Lower the bowl. Remove the agitator and bowl. 2. While holding the wire cage securely with both han

– 22 –CLEANINGWARNING: DISCONNECT THE ELECTRICAL POWER TO THE MACHINE AND FOLLOWLOCKOUT / TAGOUT PROCEDURES.New mixer bowls and accessories (beaters,

– 23 –MAINTENANCEWARNING: DISCONNECT THE ELECTRICAL POWER TO THE MACHINE AND FOLLOWLOCKOUT / TAGOUT PROCEDURES.LUBRICATION Fig. 11SlidewayThe slidew

– 24 –TransmissionTo check the oil level, remove the top cover, which is secured by two screws. Remove the Transmission Fill Plug (Fig. 12) and check

– 25 –Measure Clearance Pour enough fl our in the bowl to cover the bottom of the bowl where the beater travels. With the bowl fully raised (beater sho

– 26 –TROUBLESHOOTING Symptoms Possible Causes Mixer will not start. Circuit protector is in open position - check fuse or disconnect switch. M

– 27 –AGITATORSACCESSORIESBowl Bowl Truck Splash CoverP Pastry Knife Bowl Scraper ED Dough HookI Wire Whip B Flat Beater C Wing Whip D Wire Whip

– 28 –FORM 34928 Rev C (November 2006) PRINTED IN U.S.A.NOTES

– 3 –TABLE OF CONTENTSGENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4INSTALLATION . . . . .

– 4 –Installation, Operation and Care ofLegacy® 80-Quart MixersandLegacy® 140-Quart MixersSAVE THESE INSTRUCTIONSGENERALThe Legacy® 80-quart mixer is

– 5 –INSTALLATIONUNPACKINGImmediately after unpacking the mixer, check for possible shipping damage. If this machine is found to be damaged after unpa

– 6 –ELECTRICAL CONNECTIONSWARNING: ELECTRICAL AND GROUNDING CONNECTIONS MUST COMPLY WITH THE APPLICABLE PORTION OF THE NATIONAL ELECTRICAL CODE AND/

– 7 –OPERATIONWARNING: MOVING AGITATOR IN BOWL, KEEP HANDS, CLOTHING AND UTENSILS OUT WHILE IN OPERATION. DO NOT USE WITHOUT INTERLOCKED GUARD. T

– 8 –STANDARD CONTROLSModel HL800 and HL1400 (With Four Mix Speeds Plus Stir Speed)Mixer Speeds (Model HL800 and HL1400)STIR (Slow) This speed is

– 9 –PROGRAMMABLE RECIPE TIMER (OPTIONAL)Timer Specifi cations (Model HL800 and HL1400)• Maximum number of programmable recipes: 9 recipes.• Maxim