Hobart LXiGC ML-130018 Instrukcja Użytkownika

701 S. RIDGE AVENUETROY, OHIO 45374-0001937 332-3000www.hobartcorp.comNSTRUCTIONSILXi SERIES DISHWASHERMODELSLXiC ML-130016LXiH ML-130017LXiGC ML-1300

– 10 –INSTALLATION DIAGRAM (LXiC & LXiH)WARNING:REQUIRED FLOWING WATER PRESSURE TO THE DISHMACHINE IS 20 ± 5 PSIG. IFPRESSURES HIGHER THAN 25 PSI

– 11 –INSTALLATION DIAGRAM (LXiGC & LXiGH)CONNECTION INFORMATION(AFF = ABOVE FINISHED FLOOR)LEGENDE1 ELECTRICAL CONNECTION: 1-3/8" DIA. HOLEF

– 12 –CHEMICAL SANITIZER (LXiC AND LXiGC)CAUTION: Items such as pewter, aluminum and silver will be attacked by sodium hypochlorite(bleach). Therefore

– 13 –OPERATING THE LXi DISHWASHERSIHTOD SWOHSYALPSID SKRAMER.NOsserP.rebmunledoMsihT.kcehc-flessmrofreprehsawhsiD.sdnoces01-5sekaterutarepmetpmusdnat

– 14 –DIAGNOSTIC MESSAGESIn the event of a problem with a temperature probe, the display will flash P1, P2 or P3 every second.The respective heaters w

– 15 –PREPARATIONMake sure the coarse (Fig. 7) and fine (Fig. 8) strainers are in place and free of debris. Check both washarms and rinse arms to make

– 16 –DO'S AND DON'TS FOR YOUR NEW HOBART DISHWASHERDO assure proper water hardness.DO prescrape dishes thoroughly.DO use only detergents re

– 17 –CLEANINGThis machine must be cleaned at least once each working day. Use only products formulated to be safeon stainless steel.1. Press OFF. The

– 18 –PRIMING CHEMICAL PUMPSWhen a chemical becomes empty, the priming operation starts automatically the next time the machineis turned on or a wash

– 19 –MAINTENANCEDELIMINGWARNING: DELIMING SOLUTION, RINSE AGENTS OR ANY OTHER KIND OF ACID MUST NOTCOME IN CONTACT WITH BLEACH OR RINSE SOLUTION CONT

– 2 –© HOBART CORPORATION, 2003

– 20 –TROUBLESHOOTINGThis section outlines various symptoms and possible causes that may be encountered in the event ofabnormal machine operation. If

– 21 –Symptom Possible CausesUnexpected results on 1. Etching - usually caused by any combination of highdishes. temperatures, soft water, soft glass

– 22 –Symptom Possible CausesMachine fills too high or 1. Machine not level - see LEVELING in this manual.leaks from door. 2. Fill solenoid valve leak

– 23 –NOTES

– 24 –FORM 34779 Rev. B (Sept. 2005) PRINTED in U.S.A.NOTES

– 3 –TABLE OF CONTENTSGENERAL ...

– 4 –Installation, Operation and Care ofLXi SERIES DISHWASHERSSAVE THESE INSTRUCTIONSGENERALThe LXi Series dishwashers are fully automatic, front-load

– 5 –INSTALLATIONUNPACKINGImmediately after unpacking the dishwasher, check for possible shipping damage. If this machine isfound to be damaged, save

– 6 –Water SupplyA water hammer arrestor (meeting ASSE-1010 Standard or equivalent) should be installed (suppliedby others) in the common water supply

– 7 –ELECTRICAL CONNECTIONWARNING: ELECTRICAL AND GROUNDING CONNECTIONS MUST COMPLY WITH THEAPPLICABLE PORTIONS OF THE NATIONAL ELECTRICAL CODE AND/OR

– 8 –Connection Method1. Remove the cover plate at the upper right in the back of the machine (Fig. 1). A hole for 1" tradesize conduit is suppli

– 9 –OPERATOR PROGRAMMING MODEThe Operator Programming mode allows changes to be made from factory settings to the chemicalpumps’ operation. This incl