Hobart HR7E Instrukcja Użytkownika

HR7E ROTARY OVENNSTRUCTIONSI701 S. RIDGE AVENUETROY, OHIO 45374-0001937 332-3000www.hobartcorp.comFORM 35511 (Feb. 2006)MODEL HR5E & HR7E ROTARY

– 10 –SAVING OR VERIFYING A COOK PROGRAM (PROGRAM 1 – 9)Begin from Idle Mode.Program display shows last operated program (0 – 9).• Select a program (1

– 11 –Cooking 'Step 3' LED is lit.Time display blinks.• Enter the desired cook time from 0:01 (1 minute) to 6:00(6 hours).• Press ENTER to a

– 12 –PROGRAMMED COOKING (Program 1 – 9)Begin from Idle Mode.The Program display shows the last operatedprogram (0 – 9).• Select a saved cook program

– 13 –MANUAL COOKING (Program 0)Begin from Idle Mode.The Program display shows the last operated program (0 – 9).• Select manual mode by selecting pro

– 14 –HOLDING CYCLE (SILENCING THE 'END OF CYCLE' ALARM)After a cook cycle has been completed, the beeper soundsand the oven automatically e

– 15 –ADDING COOK TIME• Press ADD5 MIN during a cooking cycle to add 5 minutesof cook time to the current step of the program inprocess. Press during

– 16 –SUGGESTED ROASTING GUIDELINESThe suggested cooking times and temperatures in the table may require adjustment for properdoneness depending on in

– 17 –STEP 1STEP 2STEP 3STEP 4TEMPERATURE TIMESTEP 1STEP 2STEP 3STEP 4TEMPERATURE TIMESTEP 1STEP 2STEP 3STEP 4TEMPERATURE TIMESTEP 1STEP 2STEP 3STEP 4

– 18 –Bring chickens from cooler.Check temperature —range should befrom 37°F to 42°F.Insert approved popper,if available; it will pop outwhen chicken

– 19 – INCORRECT SPITTING — CHICKENS ON V-SPITSWRONG — Angle of spit is in line with breast. This will splitthe backbone and could possibly result i

– 2 –© HOBART 2006TABLE OF CONTENTGENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

– 20 –WARNING: SPITS ARE SHARP. USE CARE WHEN LOADING PRODUCT. SPITTING — CHICKENS ON FORK SPITS (HR5E)Press pointed ends of spits into whole poult

– 21 –Fig. 151 Load2 Skip4 Skip5 Load6 Skip7 Load3 LoadWARNING: SPITS ARE SHARP. USE CARE WHEN LOADING PRODUCT. SPITTING — CHICKENS ON FORK SPITS (

– 22 – Loading V-Spits or Thermo-Wave Spits on the Rotor (HR5E)1. Place pointed end of V-spit into outside hole on drive side of rotor (Fig. 19).2. F

– 23 – Loading V-Spits or Thermo-Wave Spits on the Rotor (HR7E)1. Place pointed end of V-spit into outside hole on non-drive side of rotor (Fig. 24).

– 24 –PERSONAL PROTECTIVE EQUIPMENTChickens and accessories are hot. Use care during unloading by using appropriate personal protectiveequipment such

– 25 –CLEANINGWARNING: DISCONNECT THE ELECTRICAL POWER SUPPLY TO THE MACHINE ANDFOLLOW LOCKOUT / TAGOUT PROCEDURES BEFORE CLEANING OR SERVICING.Proper

– 26 –CLEANING STAINLESS STEEL SURFACES1. Wash stainless steel parts with warm soapy water.2. Rinse parts thoroughly.3. Dry with a soft clean cloth.CL

– 27 –CLEANING QUARTZ LAMPSCAUTION: Do not clean the quartz lamps in the top of the oven with soap and water.Be very careful when cleaning lamps. Lamp

– 28 –WEEKLY CLEANING — HR5E OVENSClean ceiling of oven interior to remove potential greasebuild-up.Excessive grease build-up on convection fan bladea

– 29 –4 Clean ceiling area around the elementsand convection fan (Figs. 39, 40).5. Wash vent-grate and fan blade in a sinkwith warm soapy water (Fig.

– 3 –Installation, Operation and Care ofMODEL HR5E & HR7E ROTARY OVENSSAVE THIS MANUAL FOR FUTURE REFERENCEGENERALThe HR5E and HR7E Ovens are five

– 30 –Fig. 46WEEKLY CLEANING — HR7E OVEN WITH REAR GLASS DOOR, ACCESS FROM REARClean ceiling of oven interior to remove potential greasebuild-up.Exces

– 31 –Fig. 50Fig. 51Fig. 52Fig. 49Fig. 483. Remove the center nut that secures theelement cover using a 7/16" nutdriver (Fig. 47).4. Allow the e

– 32 –8. Clean the vent-grate and fan blades (Fig. 53).Rinse and allow to dry.9. After cleaning, reinstall 2 fanblades: Mate D-shaped hole onfan onto

– 33 –Fig. 5611. Working from rear of oven, position highside of vent-grate toward rear of oven,short side faces center of oven (Fig. 56).12. Reinstal

– 34 –WEEKLY CLEANING — HR7E OVENS WITH SOLID BACK, ACCESS FROM FRONTClean ceiling of oven interior to remove potential greasebuild-up.Excessive greas

– 35 –3. Using a 7/16" nutdriver, remove the centernut that secures the element cover (Fig. 61).Allow the element cover to swing down towardyou (

– 36 –Fig. 675. With element cover in forwardmostposition, lift up right side to clear righthinge pin; then lower right side and liftup left corner un

– 37 –9. After cleaning, reinstall 2 fanblades: Mate D-shaped hole onfan onto D-shaped shaft; thentighten nut (counterclockwise)(Fig. 68).Fig. 68CENT

– 38 –Fig. 73HIGH SIDETOWARD REARSHORT SIDETOWARD CENTERFig. 71Fig. 7212. Swing element cover back and raise up toclear rotor support and rotor arm (F

– 39 –15. Reinstall vent-grate: Tighten 7/16" nutson each side of vent grate using a 7/16"nutdriver (Fig. 74).Fig. 74THREAD NUTS ON BOTH SI

– 4 –ELECTRICAL CONNECTIONSWARNING: ELECTRICAL AND GROUNDING CONNECTIONS MUST COMPLY WITH THEAPPLICABLE PORTIONS OF THE NATIONAL ELECTRICAL CODE AND /

– 40 –FORM 35511 (Feb. 2006) PRINTED IN U.S.A.TROUBLESHOOTINGPROBLEM POSSIBLE CAUSE1. Control does not light up. 1. ON-OFF switch is not pressed ON.2.

– 5 –ELECTRICAL DATAHR5E HR5E / HR5E *VOLTAGE HZ PHASE AMPERAGE WATTAGE AMPERAGE208(2W) 50/60 1 26.9 6000 53.8240(2W) 50/60 1 25.0 6000 50.0208(3W)

– 6 –PLACING THE ROTOR IN THE OVEN (HR5E)The rotor must properly engage with the drive mechanism. Orient the rotor so that the end plate withthe driv

– 7 –PLACING THE ROTOR IN THE OVEN (HR7E)The rotor must properly engage with the drive mechanism. Orient the rotor so thatthe end plate with square d

– 8 –OPERATIONWARNING: HOT GLASS, GREASE AND PARTS CAN CAUSE BURNS. USE CARE WHENOPERATING AND SERVICING THE OVEN.CONTROLS (Fig. 9)MAIN POWER SWITCH —

– 9 –INITIAL STARTUPPower OnToggle the Main Power switch on the front panel of the oven to the ON position; the red indicator lighton the switch comes